開源 小型人形與雙足
Open Duck Mini v2 迷你雙腳鴨
受迪士尼 BDX 機器人啟發的開源迷你雙足機器人:約 42 cm,16 個關節,14 個飛特總線舵機,強化學習行走已實現 sim2real,整套 BOM 約 400 歐元。
- 類型
- 小型雙足
- 關節
- 16
- 高度
- 約 42 cm
- 舵機
- 飛特 STS3215 × 14
- 物料成本
- 約 398 歐元
- 結構
- PLA + TPU 列印件
- 開源硬體與開源程式碼
- 完整物料清單,附購買鏈接
- 直達原項目的圖紙、程式碼和論文
01 — 項目詳情
概況、物料清單與資料
項目概況
Open Duck Mini 由 Antoine Pirrone 和社群開發,Hugging Face 與 Pollen Robotics 贊助。它用 MuJoCo Playground 訓練行走策略,在 Raspberry Pi Zero 2W 上即時運行。
每條腿 5 個關節,加上頸部和頭部 4 個、天線 2 個。社區也做了外殼、急停面板和頭部的改裝件,並有中文搭建指南。
關鍵參數
| 舵機 | 14 × Feetech STS3215 7.4 V 總線舵機 + 9 g 舵機(天線) |
|---|---|
| 主控 | Raspberry Pi Zero 2W + Waveshare 總線舵機驅動板 |
| 感應器 | BNO055 IMU、足底接觸開關;選購攝影機、麥克風 |
| 電源 | 2 × 18650(2S)+ BMS + 5 V UBEC |
物料清單 BOM
總計 EUR 398.10(估計最低 EUR 331.10);加上可選「表情包」(眼燈、投影、喇叭、麥克風、相機)共 EUR 432.34。
| 零件 | 型號 / 規格 | 數量 | 單價 | 小計 | 購買連結 |
|---|---|---|---|---|---|
| Power | |||||
| 18650 cell | 2 | €5.00 | €10.00 | nkon.nl ↗ | |
| 18650 cell holder | 1 | €4.99 | €4.99 | amazon.fr ↗ | |
| 2S BMS | 1 | €8.40 | €8.40 | shorturl.at ↗ | |
| 5V regulator | 1 | €4.00 | €4.00 | shorturl.at ↗ | |
| Small power switch | 1 | €4.49 | €4.49 | amazon.fr ↗ | |
| usb-c charger | 1 | €9.99 | €9.99 | amazon.fr ↗ | |
| 2.1mm barrel jack | 2 | €1.00 | €2.00 | amazon.fr ↗ | |
| XT15? XT30 ? | 1 | €8.00 | €8.00 | amazon.fr ↗ | |
| Servos, control and sensors | |||||
| IMU (BNO055) | 1 | €40.00 | €40.00 | amazon.fr ↗ | |
| Raspberry pi zero 2w | 1 | €26.08 | €26.08 | t.ly ↗ | |
| SD card | 1 | €10.00 | €10.00 | amazon.fr ↗ | |
| Servo control board | 1 | €5.00 | €5.00 | waveshare.com ↗ | |
| Feetech 7.4v STS 3215 | 14 | €14.00 | €196.00 | alibaba.com ↗ | |
| Feet contact switches (SS-10) | 4 | €1.00 | €4.00 | fr.aliexpress.com ↗ | |
| 9g servos | 2 | €3.33 | €6.66 | amazon.fr ↗ | |
| MISC | |||||
| 3D printing M3 inserts | 1 | €5.99 | €5.99 | amazon.fr ↗ | |
| Standard PLA | 1 | €20.00 | €20.00 | ||
| TPU | 1 | €0.00 | €0.00 | ||
| Cable sheath | 1 | €9.00 | €9.00 | amazon.fr ↗ | |
| 15cm micro usb to usb-c cable | 1 | €7.00 | €7.00 | amazon.fr ↗ | |
| 50cm micro usb to usb c cable | 1 | €6.00 | €6.00 | amazon.fr ↗ | |
| Bearing | 3 | €3.50 | €10.50 | amazon.fr ↗ | |
| 合计 | €398.10 | ||||
可选件、工具与参考条目(不计入合计)
| 零件 | 型号 / 规格 | 数量 | 单价 | 小计 | 购买链接 |
|---|---|---|---|---|---|
| Expression package | |||||
| Projector reflector | 1 | €2.00 | €2.00 | fr.aliexpress.com ↗ | |
| Speaker | 1 | €6.00 | €6.00 | amazon.fr ↗ | |
| Leds (for eyes and projector) | 3 | €0.20 | €0.60 | amazon.fr ↗ | |
| Microphone | 1 | €15.00 | €15.00 | amazon.fr ↗ | |
| Eye diffusers | 4 | €0.16 | €0.64 | amazon.fr ↗ | |
| Amplifier | 1 | €5.00 | €5.00 | amazon.fr ↗ | |
| Raspberry pi camera | 1 | €5.00 | €5.00 | fr.aliexpress.com ↗ | |
| 合计 | €398.10 | ||||
3D 打印与制造
- 全部零件用标准 PLA、15% 填充;脚底 foot_bottom_tpu 用 TPU、40% 填充。
- PLA 约 500 g;需要 M3 热熔螺母。
- 官方 36 种 STL 在 GitHub 的 print 目录;社区改装件(外壳、头部)见同仓库 mods。
图纸、程序与论文
大文件(CAD、STL、STEP、代码仓库)请直接从原项目获取:
- GitHub 主仓库 ↗github.com
- CAD(Onshape) ↗cad.onshape.com
- 官方 BOM(Google 表格) ↗docs.google.com
- 运行时代码(Pi Zero 2W) ↗github.com
- 强化学习训练 Playground ↗github.com
- 参考动作生成 ↗github.com
- Tnkr 搭建指南 ↗tnkr.ai
- 中文搭建指南(飞书) ↗zihao-ai.feishu.cn
开源协议
主仓库 Open_Duck_Mini 为 Apache-2.0。Open_Duck_Mini_Runtime、Open_Duck_Playground、Open_Duck_reference_motion_generator 三个仓库目前没有 LICENSE 文件(2026-10-21 核对),默认保留所有权利,只能参考。
图片来源与授权
- 图 1:Antoine Pirrone(apirrone)及社区贡献者 · 仓库 Apache-2.0,图片未单独声明 — 来源 ↗
- 图 2:Antoine Pirrone(apirrone)及社区贡献者 · 仓库 Apache-2.0,图片未单独声明 — 来源 ↗
- 图 3:Antoine Pirrone(apirrone)及社区贡献者 · 仓库 Apache-2.0,图片未单独声明 — 来源 ↗
- 图 4:Antoine Pirrone(apirrone)及社区贡献者 · 仓库 Apache-2.0,图片未单独声明 — 来源 ↗
- 图 5:Antoine Pirrone(apirrone)及社区贡献者 · 仓库 Apache-2.0,图片未单独声明 — 来源 ↗
來源:圖片與資料來源:Open Duck Mini 專案(Antoine Pirrone 與社區,GitHub apirrone/Open_Duck_Mini)。主倉庫 Apache-2.0。外觀設計靈感來自迪士尼 BDX,本站與迪士尼及原項目均無隸屬關係。
顯示原文 (English)
Overview
Open Duck Mini is built by Antoine Pirrone and the community, sponsored by Hugging Face and Pollen Robotics. Walking policies are trained in MuJoCo Playground and run on a Raspberry Pi Zero 2W.
Five joints per leg, four in the neck and head, and two antennas. The community has added shell, e-stop panel and head mods, and there is a Chinese build guide.
Key specifications
| Servos | 14 × Feetech STS3215 7.4 V bus servos + 9 g servos (antennas) |
|---|---|
| Controller | Raspberry Pi Zero 2W + Waveshare bus-servo driver |
| Sensors | BNO055 IMU, foot contact switches; optional camera and mic |
| Power | 2 × 18650 (2S) + BMS + 5 V UBEC |
Bill of materials
Total €398.10 (estimated minimum €331.10); with the optional expression package (eye LEDs, projector, speaker, mic, camera) €432.34.
Download the BOM (.xlsx) · Official BOM ↗
| Part | Model / spec | Qty | Unit | Subtotal | Supplier |
|---|---|---|---|---|---|
| Power | |||||
| 18650 cell | 2 | €5.00 | €10.00 | nkon.nl ↗ | |
| 18650 cell holder | 1 | €4.99 | €4.99 | amazon.fr ↗ | |
| 2S BMS | 1 | €8.40 | €8.40 | shorturl.at ↗ | |
| 5V regulator | 1 | €4.00 | €4.00 | shorturl.at ↗ | |
| Small power switch | 1 | €4.49 | €4.49 | amazon.fr ↗ | |
| usb-c charger | 1 | €9.99 | €9.99 | amazon.fr ↗ | |
| 2.1mm barrel jack | 2 | €1.00 | €2.00 | amazon.fr ↗ | |
| XT15? XT30 ? | 1 | €8.00 | €8.00 | amazon.fr ↗ | |
| Servos, control and sensors | |||||
| IMU (BNO055) | 1 | €40.00 | €40.00 | amazon.fr ↗ | |
| Raspberry pi zero 2w | 1 | €26.08 | €26.08 | t.ly ↗ | |
| SD card | 1 | €10.00 | €10.00 | amazon.fr ↗ | |
| Servo control board | 1 | €5.00 | €5.00 | waveshare.com ↗ | |
| Feetech 7.4v STS 3215 | 14 | €14.00 | €196.00 | alibaba.com ↗ | |
| Feet contact switches (SS-10) | 4 | €1.00 | €4.00 | fr.aliexpress.com ↗ | |
| 9g servos | 2 | €3.33 | €6.66 | amazon.fr ↗ | |
| MISC | |||||
| 3D printing M3 inserts | 1 | €5.99 | €5.99 | amazon.fr ↗ | |
| Standard PLA | 1 | €20.00 | €20.00 | ||
| TPU | 1 | €0.00 | €0.00 | ||
| Cable sheath | 1 | €9.00 | €9.00 | amazon.fr ↗ | |
| 15cm micro usb to usb-c cable | 1 | €7.00 | €7.00 | amazon.fr ↗ | |
| 50cm micro usb to usb c cable | 1 | €6.00 | €6.00 | amazon.fr ↗ | |
| Bearing | 3 | €3.50 | €10.50 | amazon.fr ↗ | |
| Total | €398.10 | ||||
Optional items, tools and reference items (not counted)
| Part | Model / spec | Qty | Unit | Subtotal | Supplier |
|---|---|---|---|---|---|
| Expression package | |||||
| Projector reflector | 1 | €2.00 | €2.00 | fr.aliexpress.com ↗ | |
| Speaker | 1 | €6.00 | €6.00 | amazon.fr ↗ | |
| Leds (for eyes and projector) | 3 | €0.20 | €0.60 | amazon.fr ↗ | |
| Microphone | 1 | €15.00 | €15.00 | amazon.fr ↗ | |
| Eye diffusers | 4 | €0.16 | €0.64 | amazon.fr ↗ | |
| Amplifier | 1 | €5.00 | €5.00 | amazon.fr ↗ | |
| Raspberry pi camera | 1 | €5.00 | €5.00 | fr.aliexpress.com ↗ | |
| Total | €398.10 | ||||
3D printing & fabrication
- All parts in standard PLA at 15% infill; foot_bottom_tpu in TPU at 40%.
- About 500 g of PLA; M3 heat-set inserts required.
- The 36 official STLs are in the repository’s print folder; community mods (shell, head) are alongside.
CAD, code & papers
Get the large files — CAD, STL, STEP and code — straight from the original project:
- GitHub (main) ↗github.com
- CAD (Onshape) ↗cad.onshape.com
- Official BOM (Google Sheets) ↗docs.google.com
- Runtime (Pi Zero 2W) ↗github.com
- RL training (Playground) ↗github.com
- Reference motion generator ↗github.com
- Build guide on Tnkr ↗tnkr.ai
- Chinese build guide (Feishu) ↗zihao-ai.feishu.cn
License
The main Open_Duck_Mini repository is Apache-2.0. Open_Duck_Mini_Runtime, Open_Duck_Playground and Open_Duck_reference_motion_generator have no LICENSE file (checked 2026-10-21), so all rights are reserved by default — reference only.
Image credits
- Image 1: Antoine Pirrone (apirrone) and community contributors · repo Apache-2.0, image not separately licensed — source ↗
- Image 2: Antoine Pirrone (apirrone) and community contributors · repo Apache-2.0, image not separately licensed — source ↗
- Image 3: Antoine Pirrone (apirrone) and community contributors · repo Apache-2.0, image not separately licensed — source ↗
- Image 4: Antoine Pirrone (apirrone) and community contributors · repo Apache-2.0, image not separately licensed — source ↗
- Image 5: Antoine Pirrone (apirrone) and community contributors · repo Apache-2.0, image not separately licensed — source ↗
獲取零件
去哪裡買零件
物料清單裡的每一項都附有原團隊使用的購買連結。需要幫忙購買零件或代打 3D 列印件?告訴我們你在做哪一台機器人。
02 — 相關机器人